Opel Astra, Zafira

Since 1998 of release

Repair and car operation



Opel Astra
+ Cars Opel Astra and Zafira
+ The operation manual
+ Routine maintenance
+ The engine
+ Systems of cooling, heating
- The power supply system and release
   - The power supply system
      Sbrasyvanie pressure in the power supply system of petrol engines
      Check of a condition and replacement of fuel lines and them штуцерных connections
      Removal of air from a fuel path of the diesel engine
      Removal of pollution from the power supply system of the diesel engine
      Removal and installation of components of an inlet air path
      Removal, installation and adjustment of a cable of gas - petrol models
      Removal and installation of a pedal of an accelerator
      Removal and installation of the fuel pump - petrol models
      Removal and installation of the gauge of a stock of fuel
      Removal and installation of a fuel tank
      Removal and installation of the case of a throttle - petrol models
   + System of injection of fuel of petrol engines
   + Systems of injection and turbo-supercharging of the diesel engine
   + Systems of release and decrease in toxicity of the fulfilled gases
+ Engine electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment


Removal, installation and adjustment of a cable of gas - petrol models

Removal

 PERFORMANCE ORDER

  1. In an impellent compartment shift a clamp and disconnect the core of a cable of gas from the lever of a drive throttle заслонки.
  1. Liberate a cover of a cable from a basic arm, - try not to lose an adjusting bracket. Having walked on all cable, liberate it from intermediate clamps, try to remember a route of a lining of a cable.
  1. On the models equipped АТ, disconnect electroconducting from built in in тросовую assemblage of the gauge-switch of a mode kickdown.
  2. In car salon, for the purpose of providing of access to pedal assemblage, release fixture and remove the left (driver's) bottom section of furnish of the panel of devices.
  1. Under the panel of devices liberate a tip of a cable from assemblage of a pedal of an accelerator.
  1. Having returned to an impellent compartment, liberate from a back partition the plug of a cover of a cable through passage. Remove a cable in gathering with the plug.
  1. Check up a cable on presence of signs of deterioration and mechanical damages. In case of need make replacement.

Plugs through passage can be replaced in an individual order.

Installation

 PERFORMANCE ORDER

  1. From an impellent compartment pass a cable through a partition in salon. Fix the plug through passage in the aperture in a partition.
  2. In salon strengthen a cable tip on a pedal and check up reliability of landing of the plug through passage in a partition of an impellent compartment. Establish into place the bottom section of furnish of the panel of devices.
  3. Check up correctness of a lining of a cable in an impellent compartment, track reliability of its fastening in all intermediate clamps. On models with АТ connect electroconducting to the mode gauge-switch kickdown.
  4. Connect a cable tip to the lever of a drive throttle заслонки and fix its clamp. Fix a cover тросовой assemblages in a basic arm, then adjust a tightness (see more low).

Adjustment

 PERFORMANCE ORDER

  1. In an impellent compartment remove an adjusting bracket from a cable cover.
  1. At the removed bracket make sure that the lever is taken away against the stop. Accurately having extended a cable from a tip, completely choose its weak point.
  2. Keeping a cable cover in this position, establish a bracket in last flute before a basic arm in a cover. Now the cable weak point should be minimum.
  3. Ask the assistant to squeeze out an impellent compartment of an emphasis a pedal of an accelerator and make sure of completeness of opening and throttle заслонки. At отпускании pedals заслонка should come back smoothly in a starting position.