Opel Astra, Zafira

Since 1998 of release

Repair and car operation



Opel Astra
+ Cars Opel Astra and Zafira
+ The operation manual
+ Routine maintenance
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   Specifications
   Care of components of a body and the car bottom
   Care of vinyl elements of furnish
   Care of an upholstery and carpet coverings of salon
   Repair of insignificant damages кузовных panels
   Repair seriously damaged кузовных panels
   Service of loops and car locks
   Replacement wind and the other fixed glasses
   Removal and installation of bumpers
   Removal and installation of forward wings
   Removal and installation of a decorative lattice of a radiator
   Removal, installation and cowl adjustment
   Removal and installation of loops of a cowl
   Removal and installation of components of the lock of a cowl
   Removal and installation of a cable of a drive отпускания latches of the lock of a cowl
   Removal, installation and adjustment of doors
   Removal and installation of the internal handle of a door
   Removal and installation of the external handle of a door
   Removal and installation of door-locks
   Removal and installation of cylinders of locks of forward doors
   Removal and installation of the drummer of a door-lock
   Removal and installation of door glasses
   Removal and regulator installation стеклоподъемника
   Removal and installation of a cover of a luggage space (model the Sedan)
   Removal and installation of loops of a cover of a luggage space
   Removal and installation of components of a cover of a luggage space
   Removal and installation of a door of a back (model of Hetchbek and the Versatile person)
   Removal and installation of loops of a door of a back
   Removal and installation of components of a door of a back
   Removal and installation of components of the uniform lock
   Removal and installation of components of the electric drive стеклоподъемников (at a corresponding complete set of the car)
   Removal and installation of door rear-view mirrors
   Removal and installation of glass of a door rear-view mirror
   Removal and installation of components of the electric drive of rear-view mirrors
   Removal and installation of an internal rear-view mirror
   Removal and installation of elements of the panel обтекателя a windscreen
   Removal and installation of glass of the top hatch
   Removal and installation of components of the top hatch
   Removal and installation локеров protection of wheel arches - the general information
   Removal and door installation лючка a jellied mouth of a fuel tank
   Removal and installation of elements of furnish of a body
   Removal and installation of forward seats
   Removal and installation of back seats
   Removal and installation of modules emergency натяжителей seat belts of forward seats
   Removal and installation of seat belts
   Removal and installation top regulated анкерных knots of seat belts
   Removal and installation of panels of internal furnish of salon
   Removal and installation of the central console
   Removal and installation of a ware box
   Removal and installation of the panel of devices
+ Onboard electric equipment


лечение спины

Removal and installation of door glasses

Forward doors

 PERFORMANCE ORDER

  1. Remove the panel of an upholstery of a door and a plastic isolating membrane (Removal and installation of panels of internal furnish of salon see).
  2. Completely lift glass. On the models equipped with lateral pillows of safety disconnect a negative wire from the battery and wait for a minimum 1 minute during which the condenser of the independent power supply should be discharged. Disconnect electroconducting, turn out fixture and remove the gauge of a pillow of safety in gathering with a basic arm.

The right gauge differs from left - do not mix them at installation.

  1. Drill rivets of fastening of a back directing trench стеклоподъемника to the internal panel of a door and take a trench from a doorframe through an aperture.
  1. On m оделях with электроприводными стеклоподъемниками temporarily connect the switch of a regulator and connect a negative wire to the battery. On models with manual стеклоподъемниками temporarily plant on the axis приводную the handle стеклоподъемника. Establish glass so that bolts of its fastening to a regulator were visible through apertures at doors. Turn out bolts.
  1. Incline glass forward, so, to liberate a roller стеклоподъемника from a back directing trench, then lift glass upwards and take it from a door, having taken out outside, - it is possible, in view of limitation of an aperture, it is necessary to move glass стеклоподъемником.

    A. The scheme of fastening of glass of a forward door
    1 — Screws of fastening of glass to a regulator
    2 — the Directing trench of glass

    B. Extraction of glass of a forward door

A.

B.
  1. Installation is made upside-down. Establish new rivets of fastening of a directing trench. Bolts of fastening of glass to a regulator at the first stage should be tightened by hand, before a definitive tightening of bolts glass should be lifted completely, then to lower in corresponding position.

Back doors (including the fixed window leaf)

 PERFORMANCE ORDER

  1. Remove the panel of an upholstery of a door and a plastic isolating membrane (Removal and installation of panels of internal furnish of salon see).
  2. On models with электроприводными стеклоподъемниками temporarily connect the switch of a regulator and connect a negative wire to the battery. On models with manual стеклоподъемниками temporarily plant on the axis приводную the handle стеклоподъемника. Completely lower glass.
  3. Accurately extend rubber consolidation from a back directing trench of glass, then turn out the screw of fastening of the top directing trench. By means of a key of type TORX, through apertures in the internal panel of a door, turn out screws of fastening of the bottom directing trench.
  1. Accurately separate trenches from motionless glass and remove them upwards from a door. Consolidation of motionless glass should remain in a trench.

    1 — the Loose leaf of a directing trench
    2 — the Directing trench
    3 — the Sealant
    4 — the Fixed glass

  1. Lift the fixed glass upwards and remove it from a door.
  1. A little incline falling glass, liberating it from a trench стеклоподъемника and, having pulled upwards, take from a doorframe.

    Order of liberation of glass of a back door from a directing trench of a regulator стеклоподъемника

In view of limitation of an aperture, probably, it is necessary to remove partially consolidation and to move glass стеклоподъемником.

  1. Installation is made upside-down.