Opel Astra, Zafira

Since 1998 of release

Repair and car operation



Opel Astra
+ Cars Opel Astra and Zafira
+ The operation manual
+ Routine maintenance
+ The engine
- Systems of cooling, heating
   Specifications
   Antifreeze - the general data
   + System of cooling of the engine
   - Systems of ventilation, salon and air conditioning heating
      Removal and installation дефлекторов air lines
      Removal and installation of resistive assemblage приводного the electromotor of the fan of a heater
      Removal and installation приводного the electromotor of the fan of a heater
      Removal and installation of the control panel by functioning of systems of heating / of ventilation / of an air conditioning
      Removal and installation of the main case of a heater
      Removal and installation of the heat exchanger of a heater
      Removal and installation of the switch of a heater
      Check of serviceability of functioning and service of systems of heating and air conditioning
      Removal and installation of the compressor of a central air of air
      Removal and installation of the evaporator of a central air of air
      Removal and installation of the condenser of a central air of air
      Removal and installation of a receiver-dehumidifier of a central air of air
      Removal and installation of the additional fan
+ The power supply system and release
+ Engine electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment


Removal and installation of the main case of a heater

On the models equipped К/В it is necessary to make preliminary a discharge of a central air in the conditions of a specialised repair truck.


Brought to the case of a heater cables managements (execution)

  1. Clamp of a cable of a drive mixing заслонки
  2. Clamp of a cable of a drive distributive заслонки (air giving on the bottom level)
  3. Clamp of a cable of a drive distributive заслонки (air giving on top level)


Brought to the case of a heater cables managements (execution)

  1. Clamp of a cable of a drive distributive заслонки (air giving on top level)
  2. Clamp of a cable of a drive mixing заслонки

Removal

 PERFORMANCE ORDER

  1. Remove the central console and the panel of devices (the Body see the Head).
  2. Disconnect from the main case of a heater a sleeve of giving of air in back foot wells, - prepare rags for gathering of the cooling liquid following from the heat exchanger of a heater.
  3. Remove a passenger pillow of safety (the Onboard electric equipment see the Head).
  4. Open both lobbies of a door, turn out bolts with heads of type TORX and remove a steering cross-beam from a partition of an impellent compartment.
  1. On equipped К/В models cock a lay brake, поддомкратьте redock of the car and establish it on props, at a corresponding complete set remove protection картера. Remove a back support of the engine (the Engine see the Head).


  1. Turn out two fixing bolts and remove from the floor panel intended for condensate tap drainage knot.


Dismantle of drainage knot is possible and without preliminary removal of a support, however work thus essentially becomes complicated.

  1. Empty cooling system (Routine maintenance see the Head).
  2. Remove from a windscreen a plastic insert, turn out fixing bolts and remove the bottom covering panel.
  1. In an impellent compartment disconnect hoses of a heater from heat exchanger branch pipes, - preliminary mark hoses for the purpose of a guarantee of correctness of their connection at assemblage.

Firm hoses are equipped by sockets of fast joining.

  1. On equipped К/В models turn out штуцерный a bolt of a socket of a refrigerator tube on the broad valve.
  2. Take away cases воздухораспределителей from the top part of a partition of an impellent compartment.
  1. On equipped К/В models disconnect electroconducting from the valve отсечки a cooling liquid.
  1. In car salon disconnect electroconducting from the servomotor circulating заслонки and from the electromotor of the fan of a heater. Disconnect cables of management from the heater case (the Clamp of a cable of a drive distributive заслонки (air giving on top level is shown), execution) (illustrations Brought to the case of a heater management cables (execution and Brought to the case of a heater cables managements (execution) see also).
  1. Together with the assistant liberate the main case of a heater from a partition of an impellent compartment and take it from salon.

Installation

Installation is made in an order, the return to an order of dismantle of components.

In summary make refuelling of system of cooling (Routine maintenance see the Head). At a corresponding complete set drive away the car in a specialised workshop for a central air recharge. At installation of a steering cross-beam before a tightening of bolts make sure that the top directing have been established on the regular places.