Opel Astra, Zafira

Since 1998 of release

Repair and car operation


Opel Astra
+ Cars Opel Astra and Zafira
+ The operation manual
+ Routine maintenance
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
- Onboard electric equipment
   Specifications
   Search of causes of failures of an electric equipment
   Safety locks - the general information
   The relay - the general information and check of serviceability of functioning
   Removal and installation of switches
   Replacement of lamps of external lighting and alarm devices
   Replacement of lamps of internal lighting devices
   Removal and installation of external lighting/alarm devices
   Adjustment of a direction of optical axes of headlights
   Removal and installation of a combination of devices
   Removal and installation of components of the panel of devices
   Removal and installation прикуривателя
   Removal and installation of small horns of a horn
   Removal and installation of levers (leads) of screen wipers
   Removal and installation of elements of a drive of screen wipers
   Removal and installation of components of system of washing of glasses
   Check of serviceability of functioning and regenerative repair of a heater of back glass
   Removal and audiosystem installation / the navigating block
   Removal and installation of elements of remote control by audiosystem functioning
   Removal and installation of loudspeakers
   Removal and installation of the aerial of a radio receiver
   Anticreeping system and system immobilization the engine - the general information
   The gauge of speed of movement of the car (VSS) - the general information
   System of additional safety (SRS) - the general information
   Removal and installation of elements SRS
   Schemes of electric connections - the general information
   + Basic schemes of electric connections

Removal and installation of levers (leads) of screen wipers


The scheme of fastening of the lever of a screen wiper

And — the screen wiper Lever
In — to Lift in the top position

With — the Protective cap of a nut
D — the Fixing nut with a washer

The lever of a cleaner of a windscreen

 PERFORMANCE ORDER

  1. Include and again switch off screen wipers so that levers have returned to parking position and with an adhesive tape mark position of brushes on glass.
  2. Having hooked a screw-driver, uncover a spindle of an axis of the lever.
  3. Give a fixing nut and remove from a spindle a small washer (the Scheme of fastening of the lever of a screen wiper see an illustration).
  4. Take away the lever from glass and remove it with equipped шлицами spindle pins. If the lever "has become attached" and does not give in to removal, accurately hook its screw-driver, - try not to damage a paint and varnish covering кузовной panels.
  5. In case of need remove from the lever a brush (Routine maintenance see the Head).
  6. If removed, establish into place a brush for the purpose of glass protection at lever installation.
  7. Clean шлицы in the lever and on a spindle pin, then establish the lever and press a brush to glass, - track correctness of placing of a brush on glass concerning the marks put by an adhesive tape.
  8. Plant on a spindle a washer, screw a fixing nut and strongly it tighten.

The lever of a cleaner of back glass (model of Hetchbek and Versatile person / Zafira)

 PERFORMANCE ORDER

  1. Include and again switch off a screen wiper so that the lever has returned to parking position and with an adhesive tape mark brush position on glass.
  2. Having hooked a screw-driver, uncover a spindle of an axis of the lever, give a fixing nut and remove a small washer.
  3. Take away the lever from glass and remove it with equipped шлицами spindle pins. If the lever "has become attached" and does not give in to removal, accurately hook its screw-driver, - try not to damage a paint and varnish covering кузовной panels.
  4. In case of need remove from the lever a brush (Routine maintenance see the Head).
  5. If removed, establish into place a brush for the purpose of glass protection at lever installation.
  6. Clean шлицы in the lever and on a spindle pin, then establish the lever and press a brush to glass, - track correctness of placing of a brush on glass concerning the marks put by an adhesive tape.
  7. Plant on a spindle a washer, screw a fixing nut and strongly it tighten.