Opel Astra, Zafira

Since 1998 of release

Repair and car operation

плей фортуна официальный сайт

Anticreeping system and system immobilization the engine - the general information

The scheme of an arrangement of elements of anticreeping system


1 — the management Block 2 — the Contact gauge of a cowl 3 — the Light-emitting diode on the alarm system switch 4 — the ignition Lock 5 — the Ultrasonic gauge in салонном the fixture 6 — the Gauge of a condition of back glass (a heating element)	7 — the Contact gauge of a door of a back/cover of a luggage space 8 — the Lantern of illumination of a luggage space 9 — the Cylinder of the lock of a driver's door 10, 11 — Gauges-switches of illumination of salon/illumination of thresholds at opening of doors 12 — the Additional siren 13 — the Basic siren

See also the information resulted in the Head the Operation manual.

The general information

All models are equipped by the device immobilization, to effectively interfering attempts of unapproved start of the engine. The system is activated by the ignition key and built in the ignition lock the electronic gauge.

The block of management of anticreeping system by means of contact and volume gauges supervises a condition of all doors, including a door of a back / a cover of a luggage space, a cowl and the ignition lock, and also salon and luggage space volumes and a car list (the Scheme of an arrangement of elements of anticreeping system see an illustration). The management block is established in the bottom of the right forward rack at feet of the passenger and covered by the decorative panel. Ultrasonic (volume) gauges are established in the top part of the central racks and react to any changes of volume of salon. Inclination gauges react to change of a list of the car even at attempts of removal of a wheel. The basic alarm siren of anticreeping system is established at the left on a partition of an impellent compartment under a cowl, the additional siren is established under the left forward wing. On models the Versatile person and Zafira the gauge of a condition of glass is established in a luggage space, is closer to a back lateral window leaf.

Removal

Before removal of any component of anticreeping system it is necessary to disconnect a negative wire from the battery.

The block immobilization the engine / транспондера

PERFORMANCE ORDER

Remove a steering wheel and a casing of a steering column (the Suspension bracket and a steering see the Head). On the models equipped with the block with latches, remove the lock cylinder (Removal and installation of switches see), then remove the block from the case of the lock and disconnect electroconducting. On models with the block without latches, disconnect electroconducting, then remove the block from the case of the lock ignition.

At installation of the new block it is necessary for programming with application of the special equipment in the conditions of a car-care centre workshop.

The contact gauge of a cowl

PERFORMANCE ORDER

Turn out two fixing screws, remove the gauge and disconnect from it electroconducting.

The basic siren

PERFORMANCE ORDER

To remove a radiator, remove from a partition of an impellent compartment a water-reflective plate, give a fixing nut and disconnect electroconducting.

Additional siren

PERFORMANCE ORDER

Remove локер protection of an arch of the left forward wheel (the Body see the Head), disconnect electroconducting, turn out fixing bolts and remove a siren from a wing mudguard in gathering with a basic arm.

The contact gauge of a door

Removal and installation of switches see.

Components of the uniform lock

The Body see the Head.

The block of management of anticreeping system and the uniform lock

PERFORMANCE ORDER

Turn out the fixing screw and remove the bottom decorative panel of the right forward rack, then remove the lateral panel of furnish of a foot well. Disconnect electroconducting, give two fixing nuts and remove the management block.

Element of a food of a remote control

The description of procedure of replacement of an element of a food of panel DU see in the Head the Operation manual.

Installation

Installation of all components is made in an order, the return to an order of their dismantle. Elimination of any malfunctions in system should be made in the conditions of a car repair shop.