Opel Astra
+ Cars Opel Astra and Zafira
+ The operation manual
+ Routine maintenance
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
- Onboard electric equipment
Specifications
Search of causes of failures of an electric equipment
Safety locks - the general information
The relay - the general information and check of serviceability of functioning
Removal and installation of switches
Replacement of lamps of external lighting and alarm devices
Replacement of lamps of internal lighting devices
Removal and installation of external lighting/alarm devices
Adjustment of a direction of optical axes of headlights
Removal and installation of a combination of devices
Removal and installation of components of the panel of devices
Removal and installation прикуривателя
Removal and installation of small horns of a horn
Removal and installation of levers (leads) of screen wipers
Removal and installation of elements of a drive of screen wipers
Removal and installation of components of system of washing of glasses
Check of serviceability of functioning and regenerative repair of a heater of back glass
Removal and audiosystem installation / the navigating block
Removal and installation of elements of remote control by audiosystem functioning
Removal and installation of loudspeakers
Removal and installation of the aerial of a radio receiver
Anticreeping system and system immobilization the engine - the general information
The gauge of speed of movement of the car (VSS) - the general information
System of additional safety (SRS) - the general information
Removal and installation of elements SRS
Schemes of electric connections - the general information
+ Basic schemes of electric connections
|
Replacement of lamps of external lighting and alarm devices
At replacement of any lamp, pay attention to following moments:
- Remember that flasks of lamps remain hot within nearby 20 minutes after switching-off of lighting devices. Before to start to work make sure that components have definitively cooled down;
- Flasks of lamps галогенного and the xenon type are filled by gas being under pressure and at sharp stirring can blow up. Try to take such lamps only for a socle and use goggles. Remember that at a flask contact naked fingers on glass there are fatty stains that leads to a premature exit of a lamp out of operation as a result of an overheat. Before installation wipe a flask of a lamp spirit;
- Always check a condition of socles of lamps and contacts of cartridges, before lamp installation without fail smooth out contact surfaces, completely deleting from them a dirt and corrosion traces;
- Watch that the replaceable lamp in accuracy corresponded failed on the electric characteristics (pressure of a food and capacity).
Passing light of headlights
Headlights галогенного type
|
|
- Open a cowl, release fixture and turn established with the back party of an external block headlight of assemblage of a forward lantern a brown cartridge counter-clockwise.
|
A.
B. |
|
|
Passing light block headlight is external of two forward lanterns established in assemblage. The internal block headlight is a headlight headlight. |
|
- Take it from a cartridge, having grasped fingers a metal socle, - try to remember position of a lamp in a cartridge. Try not to touch a lamp flask with naked fingers, - take advantage of a napkin (see above).
|
|
- Installation is made upside-down. Track correctness of landing of pins of a socle in cartridge cuts.
|
|
Headlights of the xenon type
|
|
- Passing light block headlight is external (1) of two forward lanterns established in assemblage. The internal block headlight (2) is a headlight headlight.
|
|
- From the back party of a block headlight the protective cover is established. The passing light of headlights of the xenon type functions at very high voltage of a food!
- With a view of safety composers of the present Management recommend to charge performance replacement of lamps of a passing light to experts of car-care centre.
|
|
Headlight of headlights
Headlights галогенного type
|
|
- Open a cowl, release fixture and turn established with the back party of an internal block headlight of assemblage of a forward lantern a black cartridge counter-clockwise.
|
|
|
|
Headlight block headlight is internal of two forward lanterns established in assemblage. The external block headlight is a passing light headlight. |
|
- Release a clamp and disconnect from a cartridge of a lamp electroconducting. The lamp is built in a cartridge and replaced in gathering with it, - try not to touch a lamp flask with naked fingers, - take advantage of a napkin (see above).
|
|
- Installation is made upside-down. For cartridge fixing in a block headlight turn a cartridge against the stop clockwise.
|
|
Headlights of the xenon type
|
|
- Open a cowl.
|
- Remove a protective cover from an internal block headlight of lantern assemblage.
|
|
- Wring out a cartridge downwards and take it together with a lamp from a block headlight reflector.
|
|
- Having pulled, remove the tip from bayonet contacts on a lamp socle.
|
|
- Installation is made upside-down. Try not to touch a lamp flask with naked fingers, - take advantage of a napkin (see above).
|
|
Forward parking fires
Headlights галогенного type
|
|
- Open a cowl. A lamp of forward parking fire from below in a headlight block headlight. For cartridge extraction turn it counter-clockwise.
|
|
- Having pulled outside, take a lamp from a cartridge.
|
|
- Installation is made upside-down.
|
|
Headlights of the xenon type
|
|
- Open a cowl. A lamp of forward parking fire from below in a headlight block headlight. For the purpose of maintenance of adequate access remove a cartridge from a headlight lamp.
|
- Pull a cartridge of a lamp of parking fire outside and take it in gathering with a lamp from the seat in a reflector.
|
|
- Having pulled outside, take a lamp from a cartridge.
|
|
- Installation is made upside-down.
|
|
Forward indexes of turns
Headlights галогенного type
|
|
- Open a cowl, turn counter-clockwise the cartridge of white colour established in lateral section of lantern assemblage.
|
|
- In indexes of turns lamps байонетного type are used - drown a lamp in a cartridge and, having turned, take it.
|
|
- Establish a new lamp in return sequence.
|
|
Headlights of the xenon type
In lantern assemblages of the xenon type the turn index is built in in lantern assemblage and equipped by a lamp not requiring service накаливания. In case of a lamp exit out of operation composers of the present Management recommend to address to experts of car-care centre.
Antifog headlights
|
|
- Remove a forward bumper (the Body see the Head).
|
- Turn and remove корончатую a cover in a back part of lantern assemblage.
|
|
- Wring out clamps and disunite a contact socket of electroconducting of an antifog headlight.
|
|
- Release spring clamps and take a lamp from lantern assemblage, - try to remember adjusting position of a lamp in a reflector.
|
|
|
|
Replaceable lamps are delivered in gathering with food electroconducting. |
|
- Installation is made upside-down.
|
|
Repeaters of indexes of turns
|
|
- From lateral aspect of a wing of a safety lock shift a lens of the repeater (1) back and liberate its forward part from a clamp, - in case of need hook a lens the suitable tool.
- Having turned, liberate a cartridge with a lamp from a lens, then, having pulled, take бесцокольную a lamp (2) of a cartridge.
|
|
- Installation is made upside-down. At first fill in an aperture in a wing a lens first line, then, having pressed, latch the back.
|
|
The back combined lanterns
Models of Hetchbek
|
|
- In a luggage space release clamps and remove also an access cover to the block of the back combined lantern.
|
|
- Disunite a contact socket of electroconducting.
- Supporting a back lantern outside, from within turn away two screws-lambs.
|
|
- Take lantern assemblage from кузовного an aperture.
|
- Compress clamps and remove from a lantern ламподержатель.
|
|
- In back lanterns lamps байонетного type are used. Drown a lamp subject to replacement in the holder, turn it counter-clockwise and take from a cartridge.
|
|
- Installation is made upside-down.
|
|
Models the Versatile person and Zafira
|
|
- In a luggage space release clamps and remove also an access cover to the block of the back combined lantern.
|
|
- Holding a lantern outside, from within release two screws-lambs (are shown by arrows).
|
|
- Remove a lantern.
|
- Wring out clamps and remove from a lantern ламподержатель.
|
|
- In back lanterns lamps байонетного type are used. Drown a lamp subject to replacement in the holder, turn it counter-clockwise and take from a cartridge.
|
|
- Installation is made upside-down.
|
|
Lantern of illumination of licence plate
Models the Sedan and Hetchbek
|
|
- For the purpose of maintenance of adequate access open a door of a back / a luggage space cover, - the lantern of illumination of licence plate is located in the top part of a back bumper.
|
- Having passed a suitable screw-driver in a special groove under a lantern lens, release an internal clamp of fastening of lantern assemblage.
|
|
- Wring out downwards a lens right edge, lift left and liberate lantern assemblage from a bumper.
|
|
- Compress clamps and remove a lantern lens.
|
|
- Having pressed and having turned, take a lamp байонетного type from ламподержателя.
|
|
- Installation is made upside-down.
|
|
Models the Versatile person and Zafira
|
|
- Open a door of a back and fix it in the top position.
|
- Turn out fixing screws and remove corresponding of two lantern assemblages.
|
|
- Take a lamp фестонного type from spring contact legs.
- Installation is made upside-down. Track reliability of fixing of a lamp spring contacts.
|
|
Top level Stoplight
|
|
- Open a back door, remove заглушки, turn out fixing screws and remove the bottom and top sections of an internal upholstery of a door, - pay attention that the bottom panel of an upholstery is equipped by the ledges entering into gearing with grooves of the top panel.
|
- Turn out two fixing screws / release clamps, remove assemblage of a stoplight of top level and disconnect from it electroconducting.
|
A.
B. |
- The Stoplight is executed not folding and in case of failure is replaced entirely.
- Installation is made upside-down.
|
|
|
|