Opel Astra, Zafira

Since 1998 of release

Repair and car operation



Opel Astra
+ Cars Opel Astra and Zafira
+ The operation manual
+ Routine maintenance
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
- Suspension bracket and steering
   Specifications
   Removal and installation of a rotary fist
   Check of a condition and replacement ступичной assemblages
   Removal and installation of a forward stretcher
   Removal, regenerative repair and installation of a rack of a forward suspension bracket
   Removal and installation of the forward stabilizer of cross-section stability
   Removal, regenerative repair and installation of the bottom lever of a forward suspension bracket
   Replacement of the bottom spherical support
   Removal and installation back ступичной assemblages
   Check of a condition and replacement of bearings of back wheels
   Removal, check of a condition and installation of the back shock-absorber
   Removal and installation of screw springs of a back suspension bracket
   Removal and installation торсионной beams of a back suspension bracket
   Replacement резинометаллических hinges of longitudinal levers торсионной beams
   System of adjustment of a road gleam of a back axis - the general information and adjustment
   Removal and installation of the air valve and highway of a regulator of a road gleam of a back axis (model the Versatile person)
   Removal and steering wheel installation
   Removal and installation of a steering column
   Removal, check of a condition and installation of an intermediate shaft of a steering column
   Replacement of protective covers картера the steering mechanism
   Removal and installation of the steering mechanism
   Removal and installation of the steering pump
   Removal of air from hydraulic path ГУР
   Removal and installation of tips of steering draughts
   Removal and installation of steering draught
   Corners of installation of wheels
+ Body
+ Onboard electric equipment



Removal and installation of a rotary fist

Composers of the present Management recommend to replace bolts and nuts of fastening of rotary fists without dependence from their condition. For procedure performance the stripper of spherical hinges is required.


Disorder of forward wheels is regulated by position of a bolt of fastening of a fist to a rack. Before removal of bolts mark landing position of a fist concerning a rack. On termination of assemblage the geometry of a forward suspension bracket is subject to check and, - in case of need, - adjustment in the conditions of a car-care centre workshop.

Removal

 PERFORMANCE ORDER

  1. Cock a lay brake, поддомкратьте redock of the car and establish it on props. Remove a corresponding forward wheel.
  2. Release a nut of fastening of a tip of steering bent for to the lever of a rotary fist. By means of a special stripper liberate a tip from the lever (Removal and installation of tips of steering draughts see).
  3. Remove ступичную assemblage (Check of a condition and replacement ступичной assemblages see).
  4. Mark position of a fist concerning a suspension bracket rack (the prevention in the beginning see), give two nuts and take fixing bolts (pay attention that bolts are established by heads forward on the car). Separate from a fist a spherical support. Remove a fist from a rack. Fixing bolts and nuts are subject to replacement without fail.

Installation

 PERFORMANCE ORDER

  1. Plant a rotary fist on a rack and insert new fixing bolts. Make sure of correctness of combination of the landing labels put in the course of dismantle, then screw fixing nuts and in stages tighten them with demanded effort (Specifications see).
  2. Establish ступичную assemblage (Check of a condition and replacement ступичной assemblages see).
  3. Connect to a fist a tip of steering draught and tighten its nut with demanded effort.
  4. Establish a forward wheel and lower the car on the earth.
  5. Drive away the car on a car repair shop for carrying out of check and, - in case of need, - adjustments of corners of installation of forward wheels.