Opel Astra, Zafira

Since 1998 of release

Repair and car operation


Opel Astra
+ Cars Opel Astra and Zafira
+ The operation manual
+ Routine maintenance
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
- Suspension bracket and steering
   Specifications
   Removal and installation of a rotary fist
   Check of a condition and replacement ступичной assemblages
   Removal and installation of a forward stretcher
   Removal, regenerative repair and installation of a rack of a forward suspension bracket
   Removal and installation of the forward stabilizer of cross-section stability
   Removal, regenerative repair and installation of the bottom lever of a forward suspension bracket
   Replacement of the bottom spherical support
   Removal and installation back ступичной assemblages
   Check of a condition and replacement of bearings of back wheels
   Removal, check of a condition and installation of the back shock-absorber
   Removal and installation of screw springs of a back suspension bracket
   Removal and installation torsion beams of a back suspension bracket
   Replacement резинометаллических hinges of longitudinal levers torsion beams
   System of adjustment of a road gleam of a back axis - the general information and adjustment
   Removal and installation of the air valve and highway of a regulator of a road gleam of a back axis (model the Versatile person)
   Removal and steering wheel installation
   Removal and installation of a steering column
   Removal, check of a condition and installation of an intermediate shaft of a steering column
   Replacement of protective covers картера the steering mechanism
   Removal and installation of the steering mechanism
   Removal and installation of the steering pump
   Removal of air from hydraulic path ГУР
   Removal and installation of tips of steering draughts
   Removal and installation of steering draught
   Corners of installation of wheels
+ Body
+ Onboard electric equipment

Removal, regenerative repair and installation of the bottom lever of a forward suspension bracket

Internal axial bolts of fastening of the lever are subject to replacement without fail.

Removal

 PERFORMANCE ORDER

  1. Cock a lay brake, поддомкратьте redock of the car and establish it on props. Remove a corresponding forward wheel.
  2. Release a coupling bolt of a collar of fastening of a finger of the bottom spherical support to a rotary fist, - try to remember adjusting position of a bolt.
  3. Wring out the bottom lever downwards, liberate a finger of a support from a fist, then cautiously release the lever, - try not to damage пыльник a spherical support (in case of need cover with its piece of a cardboard or plastic).

If the finger is clamped in a collar hardly, dissolve the lock of the last with a chisel or the big screw-driver.

  1. Pay attention that internal axial bolts of fastening of the lever should be established by heads forward on the car. Turn out bolts and remove the lever, - in case of need hook the lever mount for the purpose of overcoming of effort of the resistance developed резинометаллическими by hinges.

Repair

 PERFORMANCE ORDER

  1. In case of need make replacement of the bottom spherical support (Replacement of the bottom spherical support see). Rezinometallichesky plugs are planted in a tightness and in case of need выпрессовываются, - at absence near at hand the press, plugs can be removed by means of a bolt, a nut, washers and a replaceable face head or from is sharp a metal pipe of suitable diameter.
  1. Before installation of new plugs grease with their silicone greasing or a solution of soap water. Against the stop запрессуйте plugs in the lever, - at installation of the back plug track, that one of its cuts has settled down opposite to an edge of lever assemblage.

Installation

 PERFORMANCE ORDER

  1. Establish the bottom lever on a stretcher and in front screw new bolts, having tightened them while only by hand.
  2. Against the stop plant a finger of a spherical support in a collar, screw a coupling bolt of a collar (a head forward on the car) and tighten it with demanded effort.
  3. Establish a forward wheel and lower the car on the earth.
  4. Now, when the car weight is completely transferred on a suspension bracket, tighten internal bolts of fastening of the lever with demanded effort.
  5. Drive away the car in a specialised workshop for check and updating of corners of installation of forward wheels.