Opel Astra
+ Cars Opel Astra and Zafira
+ The operation manual
+ Routine maintenance
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
- Suspension bracket and steering
Specifications
Removal and installation of a rotary fist
Check of a condition and replacement ступичной assemblages
Removal and installation of a forward stretcher
Removal, regenerative repair and installation of a rack of a forward suspension bracket
Removal and installation of the forward stabilizer of cross-section stability
Removal, regenerative repair and installation of the bottom lever of a forward suspension bracket
Replacement of the bottom spherical support
Removal and installation back ступичной assemblages
Check of a condition and replacement of bearings of back wheels
Removal, check of a condition and installation of the back shock-absorber
Removal and installation of screw springs of a back suspension bracket
Removal and installation torsion beams of a back suspension bracket
Replacement резинометаллических hinges of longitudinal levers torsion beams
System of adjustment of a road gleam of a back axis - the general information and adjustment
Removal and installation of the air valve and highway of a regulator of a road gleam of a back axis (model the Versatile person)
Removal and steering wheel installation
Removal and installation of a steering column
Removal, check of a condition and installation of an intermediate shaft of a steering column
Replacement of protective covers картера the steering mechanism
Removal and installation of the steering mechanism
Removal and installation of the steering pump
Removal of air from hydraulic path ГУР
Removal and installation of tips of steering draughts
Removal and installation of steering draught
Corners of installation of wheels
+ Body
+ Onboard electric equipment
|
Removal and installation of the steering mechanism
Removal
|
|
- Result forward wheels of the car in rectilinear position. Take the ignition key and block a steering wheel.
- Remove a forward stretcher (Removal and installation of a forward stretcher see).
- Turn out bolts of fastening of an arm of a back support of a suspension bracket of the power unit to a stretcher.
- At a corresponding complete set turn out fastening bolts to a stretcher of a basic arm of hoses of a high pressure.
- Get under картер the steering mechanism suitable drain capacity.
|
- Give штуцерные nuts and disconnect from картера the steering mechanism hydraulic tubes.
|
|
- Disconnect electroconducting from the steering pump, liberate a plait from intermediate clamps on a stretcher, - try to remember a correct route of a lining of wires.
- Give fixing nuts and remove assemblage of the steering pump with the tank and hydraulic lines from a stretcher / картера the steering mechanism.
|
|
On the pump of model TRW the tank of the round form, on pump Delphi/Saginaw - angular is established. |
|
- Turn out fixing bolts and remove the steering mechanism from a stretcher, - in case of need preliminary remove a bar of the stabilizer of cross-section stability (Removal and installation of the forward stabilizer of cross-section stability see).
|
|
|
|
Manufacturers recommend to make replacement of all fixing bolts without fail. |
|
- In case of need remove steering draughts (Removal and installation of tips of steering draughts and Removal and installation of steering draught see).
|
|
On the market of spare parts steering pumps both in gathering with draughts, and without the last are delivered. |
Remove from a shaft rubber sealing elements.
|
|
Installation
|
|
- Establish steering draughts with tips (Removal and installation of tips of steering draughts and Removal and installation of steering draught see), - do not forget to plant on a shaft rubber consolidations.
- Carefully wipe interfaced surfaces картера the steering mechanism and a stretcher. Establish the steering mechanism on the regular place. Screw fixing bolts and tighten them with demanded effort.
- If removed, establish into place a bar of the stabilizer of cross-section stability (Removal and installation of the forward stabilizer of cross-section stability see).
- Establish into place assemblage of the steering pump with the tank of a hydraulic liquid and connecting lines. Screw fixing nuts and tighten them with demanded effort.
- Restore initial connection of electroconducting, - fix a plait in intermediate clamps on a stretcher.
- Plant new rubber sealing rings on hydraulic tubes and connect the last to картеру the steering mechanism. Tighten накидные nuts штуцерных connections with demanded effort.
- At a corresponding complete set establish on the place on a stretcher basic hydraulic tubes / of hoses. Screw fixing bolts and tighten them with demanded effort.
- Establish on a stretcher an arm of a back support of a suspension bracket of the power unit, tighten with demanded effort fixture.
- Establish a forward stretcher on the car (Removal and installation of a forward stretcher see).
- Having pumped over system of hydrostrengthening of a wheel, remove from its path air stoppers (Removal of air from hydraulic path ГУР see).
- At the first possibility drive away the car in a specialised workshop of car-care centre for check and adjustment of a convergence of forward wheels.
|
|
|
|